How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Have you been looking for help on A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard project. If the old bathtub is conveniently available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. See to it you have qualified on your own for the work and fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you install a brand-new bath tub in your restroom if you have actually currently bought a brand-new bathtub and don't require to alter the arrangement of your previous supply of water pipes.
Your devices and also material checklist must consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Tub
Using the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leakages and tighten them if required. Load the bathtub and also inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been utilized at the very least when as this will settle it into its final setting.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that piece on Tools You Need to Install a New Bathtub when doing a search on the search engines. Do you know about another person who is interested by the niche? Why not share it. Thank you for taking the time to read it.
This Resource Report this page